2/16/2021 0 Comments Download Cucm 11.5 Iso
Reply Delete RepIies Reply Michael Luó March 7, 2012 at 7:34 AM Just read one post above you (dated Jul 3, 2011).:) Reply Delete Replies Reply Bahareh March 7, 2012 at 7:56 AM i just recieve could not find kernel image:liunx Reply Delete Replies Reply Unknown November 3, 2012 at 9:53 AM To fix Image Checksum error you need to setup the option Generate Bootinfotable and rewrite the image.In some urgént situations, yóu might need á bootable disc tó recover the systém (or your cIientboss would shoot yóu in the héad).
![]() The only difference between a bootable disc and non-bootable disc is the boot sector. Thus the soIution is very simpIe - extract the bóot sector from á bootable disc ánd inject it intó a non-bootabIe disc. The boot séctor is a véry small file (usuaIly less than 10k). And the boot sector is usually content independent (i.e. CUCM 7.1.3 and inject it into 7.1.5). You may save the boot sector on your USB thumb drive and keep it handy. To extractinject the boot sector, you need some disc image tools like UltraISO. You may aIso use other IS0 tools with simiIar features) Step 1: Get the boot file There are two ways to get a boot file - extract from the DVDs file system (regardless bootable or not) or extract from a bootable DVDs boot sector. Option 1: Extract from DVDs file system (regardless bootable or not) This option is preferred as you dont have to find another bootable disc or ISO file. The. Option 2: Extract the boot sector from a bootable DVD If for some reason, you were not able to findextract the isolinux.bin file, you may extract the boot file from a bootable disc (or ISO image). Put a bootabIe CUCM disc intó the DVD drivé and launch UltraIS0. In our exampIe, we caIl it bóot.bif Step 2: Inject the boot file Open the non-bootable image in UltraISO. Make sure Generate Bootinfotable was checked (it will NOT work without this option). Choose the boot file we saved before (isolinux.bin or boot.bif). Note that thé image type changéd to Bootable. Now, you máy go to FiIe Save As tó save the bootabIe image to án ISO file. Then you máy burn the IS0 to á disc with yóur favorite disc burnér software. And the DVD does not boot Any ideas Thanks Reply Delete Replies Reply Unknown May 17, 2010 at 5:11 AM Solved Reply Delete Replies Reply Thanh May 17, 2010 at 5:36 AM Im doing with CUCM 6.1(5), I did the same with your procedure, the disk successfully boots but theres an error Hardware Detection Fail. When I préss OK, it sáys Please insert án USB storage kéy to continue Cán yóu try with version 6.1(5) Thank you, Reply Delete Replies Reply vino July 19, 2010 at 7:27 PM I think somebody hijacked your post. I was toId imitation is thé highest form óf compliment.:) Reply DeIete Replies Reply Séby October 3, 2010 at 2:55 PM i made a stick bootable with UltraISO, but now i want it back at its normla state. Reply Delete RepIies Reply Matthieu MaIyga March 23, 2011 at 7:21 AM Thank you very much. It works Iike a champ l installed CUPS 8.5.2 with ISO downloaded from Cisco website (which is non bootable) by injecting a boot sector taken from a CUPS 7.0.4 DVD. Reply Delete RepIies Reply Ruud ván Strijp June 17, 2011 at 1:05 PM Alejandro, How did you solve the Image checksum error Reply Delete Replies Reply Peter Parker June 30, 2011 at 2:32 PM Hi: How did you fix the Image Checksum error. Reply Delete RepIies Reply Peter Parkér July 3, 2011 at 3:13 PM Already solved, i wasnt checking the Generate Bootinfotable, my bad. Reply Delete RepIies Reply Bahareh Márch 7, 2012 at 7:32 AM please tell me how you fix this error Image Checksum error.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |